Impact Wrench; Ultra Mini, 1/2”, 800nm (Green)
Impact Wrench; Ultra Mini, 1/2”, 800nm (Red)
Impact Wrench; Ultra Mini, 3/8”, 800nm (Red)
Induction Heater Kit EU Plug
Flameless rapid heat conduction reduces the risk of accidents & potential damage.
Reduces damaging the bolt and material around the equipment.
Can reach up to 500 degrees centigrade within a minute.
1 x 18mm coil(diameter of bore) (Length 20cm).
1 x 22mm coil(diameter of bore) (Length 20cm).
1 x 28mm coil(diameter of bore) (Length 20cm).
1 x 1.1m Flexible Soft Coil.
EU Plug Version.
Induction Heater Kit EU Plug 2
Principle of operation:
There is an alternating magnetic field.
The metallic object (e.g. nut), in the induction coil, acts on the induced eddy currents as an electrical resistance and thus heats up.
Allows heating of screws / nuts without severely heating surrounding components or even destroying them, as it is often the case when heated with a torch.
Within the shortest possible time, e.g. rusty nuts are heated and can be loosened.
Using for e.g. ball joint pinch bolts and other items on axle and engine.
Also for heating components such as bearings.
Includes the following induction coils:
Inductive coil 19 mm, 220 mm long (for Ø 10-16 mm).
Induction coil 27 mm, 220 mm long (for Ø 17-24 mm).
Induction coil 50 mm, 235 mm length (for heating small surfaces).
Formless coil, 780 mm, for heating of components (bearings, etc.).
Power supply: ~230V (50-60Hz).
Current: 7.5 Amps.
Max. power: 1.5 kw.
Protection class IP20.
Dimensions: 200 x 140 x 75mm.
Weight 4.5 Kg.
Induction Heater Kit UK Plug
The best way to loosen stuck bolts and parts without the need to cut or drill.
Flameless rapid heat induction reduces the risk of accidents & potential damage.
Reduces damaging the bolt and material around the equipment.
Can reach up to 500 degrees centigrade within a minute.
1 x 18mm coil(diameter of bore) (Length 20cm).
1 x 22mm coil(diameter of bore) (Length 20cm).
1 x 28mm coil(diameter of bore) (Length 20cm).
1 x 1.1m Flexible Soft Coil.
UK Plug Version.
Induction Heater Kit UK Plug 2
Principle of operation:
There is an alternating magnetic field.
The metallic object (e.g. nut), in the induction coil, acts on the induced eddy currents as an electrical resistance and thus heats up.
Allows heating of screws / nuts without severely heating surrounding components or even destroying them, as it is often the case when heated with a torch.
Within the shortest possible time, e.g. rusty nuts are heated and can be loosened.
Using for e.g. ball joint pinch bolts and other items on axle and engine.
Also for heating components such as bearings.
Includes the following induction coils:
Inductive coil 19 mm, 220 mm long (for Ø 10-16 mm).
Induction coil 27 mm, 220 mm long (for Ø 17-24 mm).
Induction coil 50 mm, 235 mm length (for heating small surfaces).
Formless coil, 780 mm, for heating of components (bearings, etc.).
Power supply: ~230V (50-60Hz).
Current: 7.5 Amps.
Max. power: 1.5 kw.
Protection class IP20.
Dimensions: 200 x 140 x 75mm.
Weight 4.5 Kg.
Induction Rope Wire for Induction Heater
Injection Pump Remover / Installer Ford ECOBlue Diesel
Set Specifically Designed For:
This set is for removing and installing injection pumps on mainly ford engines which run on ecoblue diesel.
Applications:
Ford Transit, Transit Custom and Tourneo. For Ecoblue TDCi engines: AWD, FWD, RWD 2016 onwards.
Engine codes:
YLFS, YMFS, YNFS, YLF6, YMF6, YNF6, YLR6, YMR6, YNRS. Equivalent to OEM tool 303-1635.
Injector Clamping Bolt Thread Repair Kit – Mercedes Benz CDi
Injector Thread Repair kit provides the special tools required to drill out the broken bolt and fit M6 threaded inserts to allow new OEM M6 bolts to be used.
Allows the task to be performed with minimal dismantling allows the cam cover to remain in place for immense time saving.
Size M6 threaded insert fitting kit for Use on Mercedes Benz Injector clamping bolts.
For Use On: Mercedes Benz CDi engines.
Contents: M8x1.0mm Tap, 7-8mm step drill, 6mm drill, Drill guide, insert fitting tool & 5x threaded inserts.
Replacement Inserts Available under Art: 60013-1-WW.
Injector Copper Washer Seal Kit; 375-Piece
13.8 x 7.3 x 1.4 mm x25.
14.6 x 7.5 x 1.3 mm x25.
14.6 x 7.5 x 3.0 mm x25.
15.0 x 7.0 x 2.0 mm x25.
15.0 x 7.5 x 1.0 mm x25.
15.0 x 7.5 x 1.5 mm x25.
15.0 x 7.5 x 2.0 mm x25.
15.0 x 7.5 x 2.5 mm x25.
15.0 x 7.5 x 3.0 mm x25.
15.5 x 7.5 x 2.0 mm x25.
16.0 x 7.5 x 1.5 mm x25.
16.0 x 7.5 x 1.7 mm x25.
16.0 x 7.5 x 2.0 mm x25.
16.4 x 7.5 x 2.0 mm x25.
20.0 x 9.4 x 0.9 mm x25.
Injector Pump Puller; VAG Engines
Applications:Â Audi, SEAT, Skoda and VW vehicles with direct injection pump engines. Also for engines with Pump injector units.
Should be used as OEM T10133 andT10163.
Includes:
Puller for dismantling FSI injectors(T10133/1).
Puller claw for dismantling FSI injectorsT10133/2.
Sliding hammer T10133/3.
Cone for mounting the combustion chamber rings (T10133/5).
3 calibration tools for mounting the combustion chamber rings T10133/6, T10133/7, T10133/8.
Built-in pin for mounting the FSI injectorsT10133/9.
Extractor for dismantling pump-injector units.
Injector Removal Adaptors; Universal
For pulling out hard to remove diesel injectors.
To be used with our optional sliding hammers 4212-WW.
Includes the following tools:
6 adapters for installation in the injector thread.
Inside thread M20x1.5 to inside thread M14x1.0.
Inside thread M20x1.5 to outside thread M17x1.0.
Inside thread M20x1.5 to outside thread M18x1.5.
Inside thread M20x1.5 to outside thread M20x1.0.
Inside thread M20x1.5 to outside thread M25x1.0.
Inside thread M20x1.5 to outside thread M27x1.0.
3 pulling claws with inside thread M18x1.5and claw width 12, 13 and 16 mm -ball head adapter M18x1.5 to M18x1.10 mm int.
Injector Removal Kit with Slide Hammer and Adapters; 14 pcs
Ball joint allows hammer to be used in confined areas.
Set includes keys and deep open profile sockets for.
Dismantling injectors, and adaptors.
Allows easy and quick removal of the injector.
Includes:
Sliding hammer with shaft and handle, weight 4400g.
Ball joint adaptors.
Adaptor (internal thread): m14 x m14 - m17 x m14, m25 x m14 - m27 x m14.
Adaptors (external thread): m27 x m14 - m20 x m14.
6-Pt socket for electrical unit 25 - 27 - 29 - 30.
10 Mm hexagon bit socket with 12.5-1/2 Drive.
Injector Removal Kit with Slide Hammer and Adapters; 24-Piece
Diesel Injector Master Kit.
Suitable for the removal of Bosch / Delphi / Denso / Siemens and Pumpe Duse diesel injectors.
1.3kg Slide Hammer with 150mm Shaft.
4kg Slide Hammer with 400mm Shaft and Handle.
With various Male and Female Adaptors.
Pump Duse Injectors Adaptors.
Injector Sockets - 25, 27, 29, 30mm.
Injector Removal Kit; HDI Injectors
or use in the extraction of Bosch and Siemens HDI injectors. No need to remove the cylinders heads with this kit.
Suitable for vehicles with PSA 2.0l DW10/12 engines which can also be found on Toyota, Mazda and Hyundai models.
Included2 ball bearing puller spindles 2 Open sockets for removal of the electric unit. High performance support frame with spindle bearings.
Injector Removal Master Kit; Bosch, Delphi, Denso, Siemens
Master kit for use on Bosch, Delphi, Denso and Siemens injectors.
Can also be used on non branded injectors.
Included are special adapters for internal and external threads.
For more modern injectors look for Art. 4199.
Slide hammer 1.6kg, 160mm.
Slide hammer 2.7kg, 460mm.
Slide hammer 5.1kg, 600mm.
Pulling claw 13.7 x 18 mm, 105 mm long.
Pulling claw 12.7 x 19 mm, 130 mm long.
Slotted socket 1/2'' 25, 27, 28, 29, 30mm.
Pulling adapter Internal thread M27 x 1.0 (x3), M25 x 1.
Pulling adapter External thread M27 x 1.0 (x3).
Hammer adapter for all adapters.
Injector Removal Tool Kit; Vibration Hammer Edition
Injector Remover for Bosch Injectors; Diesel
Quickly and easily remove stubborn stuck diesel injectors.
Suitable for assembling and disassembling tightly fit common rail injectors.
Suitable for e.g. Mercedes CDI engines 611, 612 and 613.
Suitable for working in confined spaces due to the low support cylinder diameter.
Special tool construction allows to pull injector with high force.
Injector Sealing Plug Set, 12-Piece
12-Piece Injector Sealing Plug Set.
For sealing Injectors prior to pressure loss Testing.
Protects the Injector from contamination during Work.
Suitable For use on: Bosch, Delphi, Siemens & Denso Injectors.
Applications: Opel-Vauxhall, Mazda, Ford-Volvo, PSA Group, Mercedes-Benz, Renault, Fiat-Chrysler & Others.
Contents: 6x M12x1.50 Caps, 6x M14x1.50 Caps.
Injector Seat Cleaners; 17-Piece
Used to clean and de-carbonise injector seats when changing injectors.
Suitable for a wide range of vehicles.
Contents:
14mm x 14mm Flat Reamer.
15mm x 19mm Flat Reamer.
15.5mm x 15.5mm Flat Reamer.
15.5mm x 15.5mm Angled Reamer.
17mm x 17mm Angled Reamer.
17mm x 17mm Flat Reamer.
17mm x 17.5mm Flat Reamer.
17mm x 19mm Flat Reamer.
17mm x 19.5mm Flat Reamer.
17mm x 20mm Flat Reamer.
17mm x 21mm Angled Reamer.
17.5mm x 20.5mm Angled Reamer.
19mm x 21.5mm Flat Reamer.
Pilot Hex 19 x 170mm.
15.5 X 250mm Cutter.
2.5mm Hex Key.
T-handle.
